Guntis Rudusans

• Lead the design & development of new test rigs and facilities

• Performed variety of testing on microturbine gensets. This includes, but is not limited to:

• Performance Testing

• Endurance and Reliability Testing

• Customer validation testing, such as testing the interaction of our product with customer equipment

• Research and Development into new product introductions, and solutions to problems, cost down, product improvement etc

• Product investigations

• Fault finding and diagnosis of problems.

• Manage data, configuration details and results in a highly organised manner.

• Reporting by writing detailed technical test reports.

• R&D and V&V test activities, new product introduction and subsystem testing.

• Fuel and ignition system analytics

• Manage tests, tear down, V&V and benchmarking

• Commission test jigs and fixtures to complete test plans

• Identify issues to upper management concisely and timely

• Maintain a safe, clean and orderly environment

• Design test system architecture in accordance with V&V tasks

• Produce technical reports to evaluate and compare product performance

• Determine the validity in the data and that tests are true and correct

• Perform root cause analysis on test failures, fixtures and equipment

• Provide advice and recommendations

• Support mechanical, electronics, firmware and integration teams in V&V activities

• Setting app all right equipment for DewesoftX live tests, full analysing writing reports

• CanBus tests , recordings, running rigs in test and live mode

• Software updates on all electrical equipment
• Analysing data from OTDR, HMI, CCTV, SDIAG, HPU, TCU, MON, BMM, TRAC, OESS, CPU, HVAC etc.
• Analysing or fault finding through Aunia, Hasler, Diadem, HMI, BMON_net, CanAnalyser, BMM battery report, Napo++, Logviewer, FileZilla, CCTV reviewer, Ipcomphy etc.
• Fault finding using a laptop, diagnostics, schematics, drawings and completing route cause analysis to a high level on functional systems and software
• Identifying any faults with the unit's electrical/mechanical systems
• Identifying simple fixes and longer-term solutions to problems
• Monitor processes and compliance in the test team
• Liaise with the management team, suppliers, and customers on issues or potential process changes
• Responsible for carrying out all the routine tests, dynamic tests and special tests
• Ensuring and maintaining calibration of all the test equipment
• Analysing and fault finding for Partial Discharge test failures
• Fault finding/investigations as required by customer or equipment warranty fail
• Able to prepare test procedures as per customer requirement
• Responsible for the maintenance of the trams and various high voltage equipment
• Signing off documentation as fit for service if no faults left and it’s ready to use
• Communicating with suppliers and customers due to updates, parts, faults
• Preparing test certs and all required documentation
• Fault finding, signing off all repairs and handling vehicle with the Test and Commissioning team
• Assembly, sub-assembly and testing

• Repairing or replacing parts

• Working on modification and upgrade projects

• Working on an interior modification, panel wiring, WiFi,

CCTV, module replacement etc.

• Remove and replace wiring looms

• Follow schematics and vehicle maintenance sheets

• Submit problem sheets which detail solution to problem/issues encountered

on work being undertaken

• Bending Steel conduits

• working on schematic diagrams, engineering drawings and wiring lists

• Knowledge of and ability to use a wide range of crimp tools

• Liaising with reliability engineers to ensure there is a continuous improvement to fleet reliability

• Carrying out inspections and checks to ensure reliability of fleet

• Carrying out work recording via both paperwork and computer (SAP)

• Carrying out routine maintenance, repair and fault finding on Electric Multiple Units.

• Investigation of test failures and non-compliances, service reliability issues

• Finding, repairing, crimping, replacing broken or damaged wires

• Repairing or replacing parts
• Working on modification and upgrade projects
• Working on an interior modification, understanding of panel wiring, WiFi, CCTV,module replacement etc.
• Remove and replace wiring looms
• Follow schematics and vehicle maintenance sheets
• Operate as a member of a work team
• Submit problem sheets which detail solution to problem/issues encountered on work being undertaken

• Software update
• Taking readings using Teradyne device, checking and testing wiring and electrical parts
• Electrical component calibration (seats, tailgate, lights, sensors...)
• Using Health check readings to find faults
• Researching faults using manufacturers' circuit diagrams and specification manuals
• Repairing or replacing faulty parts/modules/wires/sensors
• Retesting the system to make sure everything is working correctly and safely
• Electronic ignitions, alarms, immobilisers and tracking devices software update or repair
• Finding, repairing, crimping,broken or damaged wires

• Prototype
• Hold responsibility to ensure the vehicle meets the required standards as part of JLR quality assurance policy
• Supervisor responsibility for a team of people across the zone
• Completing a variety of fitting duties including engine assembly
• Adhering to health and safety at all times using the correct personal protective equipment 
• Supporting working alongside skilled team engineers to perform day to day tasks
• Rework prototype part ,work off engineering drawing
• Trimming,fitting,refit and rectification of vehicles
• Profiling of bonnet,fenders,doors,headlights,tailgate,body panels etc.
• Assembling 

• Welding
• Car repair (Break system, suspensions, car diagnostic, service and engine rebuilding)
• Car preparation for painting (Cutting, Sanding, Priming)
• Painting
• Downloading/Updating/remapping vehicle software systems
• Taking readings using diagnostic device, checking and testing wiring and electrical parts,fault finding